Serving the Las Cruces area  ·  (575) 339-1859  ·  Open Mon-Sun 7am-7pm
📞 (575) 339-1859 Free Quote

Metal Roofing in Santa Teresa, NM (88008) · Local Professionals

Las Cruces Metal Roofing · Fast response in Santa Teresa and the Las Cruces area · Free estimate 24h

✅ Metal Roofing Alliance Member 🛡️ Licensed & Insured 💸 Free Quote 24h 🕐 Mon-Sun 7am-7pm
🎯 Get a Free Quote 📞 (575) 339-1859
+272Verified Reviews
10Years in Business
4.9 ★Google Rating
24/7Available
✅ No hidden fees💳 Cards accepted🛡️ Licensed & Insured✅ Metal Roofing Alliance Member

Santa Teresa is one of the fastest-growing corners of Doña Ana County, and you can see it in the rooftops: new stucco homes in communities off Airport Road and Pete V. Domenici Boulevard, many built in the last 20 years, sitting on clean desert lots with wide streets and long sightlines to the Franklin Mountains. The sun here is relentless, and a shingle roof that would last 20 years in a milder climate often starts showing its age a lot sooner.

That is why homeowners in Santa Teresa (88008) call Las Cruces Metal Roofing. We install, repair, and replace metal roofs built for this desert: reflective panels that cut summer cooling bills, fasteners and seams that hold up to monsoon microbursts, and details that keep dust and rain out of the places shingles fail. We are a Metal Roofing Alliance member, fully insured, and we know this ZIP code well.

Metal Roofing in Santa Teresa (88008)

Santa Teresa sits on gently rising desert ground west of the Rio Grande, with caliche and sandy soil that drains fast but shifts slightly with our wet and dry cycles. Newer subdivisions here often have tight side yards and low-slope or complex roof lines with multiple valleys, which means panel layout, flashing, and fastener placement have to be planned carefully, not improvised. Wind is the other factor. Spring dust storms and July-September monsoon microbursts push hard against west-facing roof planes, and a poorly fastened panel can lift at the edge and peel back. We use screw patterns and seam attachments rated for our local wind exposure, and we pay close attention to eave and ridge details where wind gets underneath.

Our team has worked across Santa Teresa and the surrounding Las Cruces area, from newer stucco homes near the Santa Teresa Port of Entry to custom builds on larger lots with open desert exposure. We handle standing seam, corrugated and ribbed panels, stone-coated steel, metal shingles, and copper and specialty metals, plus repairs, re-fastening, and coatings when a full replacement is not yet necessary.

Our services in Santa Teresa

How a Job Works in Santa Teresa

Step 1: Call (575) 339-1859 or request a free estimate online. We schedule an on-site assessment at your Santa Teresa property, inspect the roof deck, existing underlayment, flashing, and fasteners, and talk through what you are seeing (leaks, lifted panels, hail dents, or just an aging shingle roof). You get a written scope and a clear price before any work begins.

Step 2: Once you approve, we pull the required roofing permit through the local building department and schedule the work. In Santa Teresa, that often means coordinating with HOA design review for panel profile and color, and planning material staging around tight side yards and driveway access. Our crews are fully insured, and we keep the site organized so your neighbors are not dealing with loose panels or debris.

Step 3: We finish with a full cleanup, magnet sweep for screws and nails, and a walkthrough with you to review the finished roof, warranty information, and any maintenance notes. We leave your property clean and the roof ready for the next monsoon season.

Metal roofing in Santa Teresa is priced by the square foot, and the range depends on the system you choose. Corrugated and ribbed panel roofing starts around $5.50 per square foot, metal roof installation starts at $8, standing seam starts at $10, and metal roof replacement starts at $9. Metal roof over shingles (retrofit) starts at $7, stone-coated steel and metal shingles start at $9, and copper or specialty metal starts at $20. Repairs and leak repairs start at $450, screw replacement and re-fastening at $750, flashing and chimney or skylight repair at $600, and gutters for metal roofs at $9 per linear foot. Coating and painting starts at $2.50 per square foot. The biggest cost factors are roof size and pitch, how many valleys and penetrations the roof has, whether we are tearing off or retrofitting, and how quickly the work needs to happen. Call (575) 339-1859 for a free estimate on your specific roof.

✅ Metal Roofing Alliance Member, licensed and insured for work in Santa Teresa and nearby areas.

My Santa Teresa home has a low-slope roof with several valleys. Can metal roofing work on that, and how do you handle the seams?
Yes. Many newer Santa Teresa homes have complex roof lines with low slopes and multiple valleys, and metal handles them well when the panels are laid out correctly. We use longer panels where possible to reduce seams, and we detail valleys with proper flashing and underlayment so water has a clear path off the roof. On lower slopes we follow the manufacturer's minimum pitch requirements and may recommend a standing seam profile or a specific underlayment system.
A monsoon microburst lifted some panels on my roof last summer. How fast can you get out to Santa Teresa?
Storm and wind damage calls get priority. We offer free inspections for storm damage in Santa Teresa and can usually get out within a day or two to secure the roof and document the damage. Call (575) 339-1859 and describe what you are seeing, and we will schedule a visit and help you with insurance documentation if you are filing a claim.
What does a typical metal roof replacement cost for a newer Santa Teresa home?
For a typical single-story stucco home in Santa Teresa, a metal roof replacement often lands somewhere between the low teens and low twenties per square foot depending on the system, roof complexity, and whether we remove the old roof. Standing seam costs more than corrugated panel, and copper or specialty metals cost more still. We give you a written price after inspecting the roof, so the number is based on your actual square footage and details, not a guess.
Do I need a permit to replace my roof in Santa Teresa, and who handles it?
Roofing permits are commonly required for a full replacement or re-roof in Doña Ana County, and requirements can vary by jurisdiction. We handle the permit process for you and schedule the required inspections. For the most current local rules, check with the county through the City of Santa Teresa website at https://www.donaanacounty.org or call the building department directly, since thresholds and fees can change.
My HOA has rules about roof color and panel style. Can you help me get approval before I sign a contract?
Yes. HOA design review is common in Santa Teresa's newer communities, and we can provide product specs, color samples, and panel profile information for your submittal. We recommend getting written HOA approval before ordering materials, and we can coordinate the timing so your installation does not get held up. If your roof is near a property line, we also follow setback and drainage rules so runoff does not create a neighbor issue.
Are you insured for roofing work at my Santa Teresa property?
We are fully insured, with general liability coverage and workers' compensation for our crews. We are happy to provide a certificate of insurance before work begins so you and your HOA or property manager have it on file.
What maintenance should I do on a metal roof in Santa Teresa between monsoon seasons?
The main things are keeping the roof clear of debris and checking fasteners and sealant points once a year, ideally in late spring before the July-September storms. Dust and grit accumulate in valleys and behind penetrations, and fasteners can back out slightly over time with our temperature swings. A quick inspection and re-fastening now can prevent a leak later. We offer free estimates for inspections and can set up a simple annual check.

Nearby service areas

📍 Las Cruces 88001📍 Mesilla 88046📍 Doña Ana 88032📍 Organ 88052
Why choose us?

Trusted professionals in Las Cruces

🏅

Licensed contractors

Continuous training, professional equipment, meticulous and code-compliant work

🛡️

Licensed & Insured

Full coverage on all our job sites, no exceptions

⚡

Available Mon-Sun 7am-7pm

Emergencies, weekends, holidays: available when you need us

💰

100% Free Quote

Response within 24h, no commitment, by phone or form

Our services

Our Metal Roofing Services in Las Cruces

All your work handled by qualified professionals in Las Cruces

Metal Roof Installation

Complete metal roof systems engineered for your local climate and built to outlast three shingle roofs.

Included in your service

  • Deck inspection and repair before any panel goes on
  • High-temp synthetic underlayment and correct ridge and soffit ventilation
  • Manufacturer-certified panel, trim, and flashing details for the full warranty
  • Free on-site assessment and written estimate within 24h
Learn more→

Standing Seam Metal Roofing

Concealed-fastener standing seam: no exposed screws to loosen, leak, or need re-torquing.

Included in your service

  • Panels roll-formed to the exact length of your roof, no end laps
  • Mechanically seamed or snap-lock profiles with concealed clips
  • Floating clip system that lets panels expand and contract freely
  • Kynar 500 / PVDF finish in the full architectural color range
Learn more→

Metal Roof Replacement

Full tear-off of an end-of-life shingle, cedar, or metal roof, replaced with a complete new system.

Included in your service

  • Tear-off and haul-away of the old roofing, dumpster included
  • Decking inspected board by board, rot and soft spots replaced
  • New underlayment, drip edge, valleys, and penetration flashing throughout
  • Documentation of the finished system for your insurer or future buyer
Learn more→

Metal Roof Over Shingles (Retrofit)

Retrofit metal installed over sound existing shingles: no tear-off, less waste, lower cost.

Included in your service

  • Honest deck and shingle assessment first, recover only when it is the right call
  • Furring strips or slip sheet as the panel profile and local code require
  • Existing vents, pipe boots, and flashings reworked to the new roof plane
  • Straight guidance on when tear-off is the better long-term choice
Learn more→

Metal Roof Repair

Targeted repair of damaged, loose, or storm-hit metal roofing before it reaches your ceiling.

Included in your service

  • Bent, dented, or punctured panels replaced and color-matched
  • Seams, laps, and penetrations resealed with compatible butyl and sealant
  • Failed pipe boots, closures, and ridge cap fasteners renewed
  • Written findings with photos of what we found and what we fixed
Learn more→

Metal Roof Leak Repair

Priority leak response: we trace the leak to its real source instead of caulking the symptom.

Included in your service

  • Water testing and interior tracing to find the true entry point
  • Backed-out fasteners, separated seams, and flashing gaps corrected at the cause
  • Emergency tarping available same day after a storm
  • Attic and insulation moisture check so hidden damage does not sit and spread
Learn more→

Screw Replacement & Re-Fastening

The top cause of leaks on 15 to 30 year old screw-down roofs, fixed for a fraction of replacement.

Included in your service

  • Every fastener replaced with oversized screws and new EPDM sealing washers
  • Dried-out washers and stripped holes addressed panel by panel
  • Ridge, eave, and sidewall closures renewed at the same time
  • Restores a watertight roof without replacing sound panels
Learn more→

Corrugated & Ribbed Panel Roofing

Corrugated, tuff-rib, and 5V panel roofing: the budget-friendly workhorse for homes and outbuildings.

Included in your service

  • Galvalume and painted steel panels cut to length on site
  • Correct screw pattern and torque so washers seat without over-driving
  • Foam and metal closures at ridge, eave, and rake to keep weather and pests out
  • Full color range for homes, cabins, barns, and workshops
Learn more→

Metal Shingle Roofing

The look of architectural shingle, slate, or shake with the lifespan and wind rating of steel.

Included in your service

  • Interlocking stamped steel or aluminum shingle panels
  • Walkable finished surface, easier to service than a standing seam field
  • Lightweight enough for retrofit over an existing roof structure
  • Profiles and colors that suit historic and HOA-governed neighborhoods
Learn more→

Stone-Coated Steel Roofing

Steel strength under a textured stone finish, with strong hail and wind performance.

Included in your service

  • Acrylic-bonded stone granule surface over structural steel
  • Battened or direct-to-deck installation depending on the profile
  • Class A fire rating and high impact resistance ratings
  • Tile, shake, and shingle textures for suburban and coastal homes alike
Learn more→

Copper & Specialty Metal Roofing

Copper, zinc, and aluminum for porches, bay windows, dormers, and full architectural roofs.

Included in your service

  • In-house fabrication of pans, valleys, and custom curved details
  • Soldered seams and joints where the detail calls for it
  • Isolation of dissimilar metals to prevent galvanic corrosion
  • A living patina that develops over decades of service
Learn more→

Metal Roof Coating & Painting

Restoration for faded, chalking, or surface-rusted metal, adding 10 to 15 years without replacement.

Included in your service

  • Wash, degrease, and mechanical prep of the entire panel surface
  • Rust treatment and primer on affected areas before topcoat
  • High-performance elastomeric or silicone coating system applied to spec
  • Honest assessment first: we say so when the roof is past coating
Learn more→

Flashing, Chimney & Skylight Repair

Flashing is the number one leak point on any metal roof, and it is what we fabricate best.

Included in your service

  • Custom bent step, counter, and apron flashing made in-house
  • Chimney crickets to shed water on the uphill side
  • Skylight curbs and head flashing rebuilt to the panel profile
  • Valley and wall transition details closed with matching trim
Learn more→

Snow Guards & Ice Protection

Snow retention that stops rooftop avalanches onto decks, gutters, walkways, and entryways.

Included in your service

  • Pad-style guards or continuous rail systems matched to your panel
  • Layout calculated from roof pitch, panel length, and local snow load
  • Clamp-on mounting on standing seam, no panel penetrations
  • Ice dam and eave detailing for higher-elevation homes
Learn more→

Storm & Wind Damage Repair

Wind, hail, and fallen-limb repair with thorough documentation and a straight repair-or-replace answer.

Included in your service

  • Free post-storm inspection with dated photo documentation
  • Emergency tarping and temporary weatherproofing when needed
  • A written report you can use when documenting your insurance claim
  • Honest assessment of repair versus replacement, with no pressure either way
Learn more→

Metal Roof Inspection

A written, no-obligation assessment of fastener condition, seams, flashing, and remaining service life.

Included in your service

  • Fastener, washer, and seam condition checked across the field
  • Flashing, penetrations, and closures inspected point by point
  • Coating wear, chalking, and corrosion graded panel by panel
  • Written report with photos and a straight answer on years remaining
Learn more→

Gutters for Metal Roofs

Gutters sized and hung correctly for metal roofing, where standard hangers and spacing do not work.

Included in your service

  • Seamless aluminum or half-round systems formed on site
  • Hanger placement and spacing matched to the panel profile
  • Oversized capacity and downspouts sized for heavy regional rainfall
  • Bracket spacing tightened for high-wind zones so storms do not tear the gutter off
Learn more→

Commercial & Agricultural Metal Roofing

Barns, workshops, churches, and light commercial metal roofing across the county.

Included in your service

  • Long-run panels for wide spans and low-slope structures
  • Purlin and framing attachment detailed for the building type
  • Insulation, vapor barrier, and condensation control options
  • Repairs and re-fastening for aging agricultural metal buildings
Learn more→
Verified client reviews

272+ Verified Client Reviews in Las Cruces

⭐⭐⭐⭐⭐ 4.9/5 · 272 verified Google reviews

David L.
⭐⭐⭐⭐⭐
DL
David L.
Organ

“Had these guys put up the metal roof on our equipment hangar out on the east mesa. About 3,000 square feet of corrugated panel, and the crew knocked it out in four days flat. Straight lines, no leaks, and they hauled off every last scrap.”

Commercial Metal Roofing
Chris A.
⭐⭐⭐⭐⭐
CA
Chris A.
Mesilla

“Our old adobe place had a flat roof that was nothing but trouble, so we had them tear it down to the deck and put on a standing seam metal roof with a proper pitch. They matched the flashing to the parapet walls like they'd done it a hundred times, and the house hasn't leaked through two monsoons since.”

Metal Roof Replacement
Jennifer M.
⭐⭐⭐⭐⭐
JM
Jennifer M.
Chaparral

“Half the screws on my orchard barn roof had backed out and it was starting to whistle in the wind. They came out, replaced every loose fastener, and resealed around the vents. Fair price and they actually showed up when they said they would.”

Metal Roof Repair
Sarah W.
⭐⭐⭐⭐⭐
SW
Sarah W.
Las Cruces

“We went with standing seam in a matte charcoal finish and it completely changed the look of the house. The crew of five was in and out in under a week, and they swept the yard with a magnet for nails before they left. Couldn't be happier.”

Standing Seam Metal Roofing
Tom D.
⭐⭐⭐⭐
TD
Tom D.
Radium Springs

“Found a wet spot on the ceiling after a storm and these folks tracked it to a failed seam around the chimney. They got it sealed up and did a full inspection while they were up there. Only gripe is it took a few days to get on the schedule, but the repair itself was solid.”

Metal Roof Leak Repair
Kevin R.
⭐⭐⭐⭐⭐
KR
Kevin R.
Doña Ana

“Was dreading a full tear-off on our place, but they laid the metal panels right over the old shingles and saved us a ton. The desert landscaping out front didn't get so much as a bent cactus from the whole job. Genuinely relieved.”

Metal Roof Over Shingles (Retrofit)
Lisa H.
⭐⭐⭐⭐⭐
LH
Lisa H.
Vado

“New metal roof on our house, and the difference in the summer heat is night and day. They walked me through the panel options and never once tried to upsell me. Two months in and not a single issue.”

Metal Roof Installation
Rachel S.
⭐⭐⭐⭐
RS
Rachel S.
Hatch

“Wanted the look of tile without the weight and cracking, so we went with stone-coated steel shingles. The color matched our old terracotta almost exactly, and the crew cleaned up so well you couldn't tell anyone had been there. They did leave a small pile of trim pieces in the driveway for a couple days, but it was gone by the weekend.”

Metal Shingle Roofing
Free Quote

Get Your Free Quote

Metal Roofing in Las Cruces · Response within 24h · No commitment · ☎ (575) 339-1859

Your Free Quote Request

Confidential · Response within 24h

✅ Free personalized estimate ⚡ Response within 24h 🛡️ Licensed & Insured 📍 On-site visits included in Las Cruces ✅ No hidden fees 🕐 Available Mon-Sun 7am-7pm